+38 (066) 354-00-04 Mon–Fri 9:00–18:00 75 Zhylianska St, Kyiv, Ukraine

Mabre biomass heat generators

Mabre heat generators on wood chips and pellets for grain dryers: up to 1.28 MW in one unit, air heated by 130 °C, stainless steel heat exchanger.

Price and configuration
Calculated for your area and conditions
Delivery
Within Ukraine and abroad, with customs clearance
Start-up and service
On-site commissioning and staff training

Description and specifications

Description

The Italian maker Mabre has been building biomass heat generators since 1972. Its main speciality is units for grain dryers: they raise the temperature of outside air by up to 130 °C and burn wood chips, wood pellets, sunflower husk pellets and nut shells. Heat reaches the dryer through a stainless steel heat exchanger, so only clean air touches the grain.

  • Up to 1.28 MW of heat in one unit; a large dryer takes two in parallel.
  • Automatic fuel feed by auger from a hopper, control from a touch panel.
  • Furnace under negative pressure: if the heat exchanger leaks, outside air is drawn into the furnace rather than smoke into the dryer.
  • Wood chips up to 20% moisture and pellets, including sunflower husk pellets.

GDSH series for grain dryers

The GDSH series in the C130 version is made for grain dryers: it heats the air to 130 °C above ambient. At −10 °C outside, the outlet is about +120 °C — enough to dry maize even in frost.

The most powerful model, GDSH 1280 C130, has a fuel input of 1,400 kW, delivers 1,280 kW of heat and supplies up to 28,300 m³/h of hot air. GDSH 1100 C130 delivers 1,170 kW and 24,200 m³/h — a unit of this size suits, for example, the Agrex AGD31 mobile grain dryer. If the dryer needs more heat, two heat generators are installed in parallel or added to an existing heat source.

  • stainless steel combustion chamber and heat exchanger;
  • ash removal from the combustion chamber;
  • 1 m³ fuel hopper with a lid, larger on request;
  • flue gas fan with frequency drive and heat exchanger turbulators;
  • control cabinet with controller and 10″ touch screen;
  • power supply 400 V, three-phase, 50 Hz.

The standard unit gives 100 Pa of free pressure: hot air is fed to the inlet of the dryer fan. The HP version develops 1,000–1,200 Pa, and then air is fed straight into the dryer without its own fan.

Safety: furnace under negative pressure

The main risk with a heat generator is a burnt-through heat exchanger: smoke and sparks enter the dryer and the grain catches fire. In Mabre units the combustion chamber runs under forced negative pressure, held by a flue gas fan under automatic control. If a leak appears in the heat exchanger, outside air is drawn in through it and no smoke goes to the dryer.

Burn-back protection in the fuel feed line is standard. A thermostatic valve and a cyclone that removes dust from the flue gases are fitted on request — where local regulations require them.

Fuel

  • class A1 wood chips, size P16–P45 (up to P16 for units up to 350 kW), up to 20% moisture; GDSH burns chips up to 23% thanks to its power reserve, wetter chips reduce output;
  • class A1 wood pellets;
  • sunflower husk pellets;
  • nut shells, peach and apricot stones, olive pomace.

Logs are not loaded by hand into these units — the GDM series is made for logs. Pellets are usually stored in a silo and chips in a bunker; we select the feed system for the site.

How the heat generator works with a dryer

Fuel falls from the hopper into an auger and is fed to the burner. Combustion gases pass through the tube bundle of the heat exchanger and leave through the stack at an average of about 170 °C. A fan blows outside air through the heat exchanger and delivers it to the dryer.

When the grain is dry, the burner is switched off and the fan keeps running — the dryer cools the grain with outside air. The heat exchanger takes about an hour to cool, so the burner is usually stopped a little before the end of drying, or a bypass valve is fitted in the duct. The controls keep the furnace on standby for up to 24 hours: after a break the burner does not need to be lit again.

The heat generator is installed indoors or under a canopy; for outdoor installation there is a monobloc version with a rain roof. We select the stack and the duct to the dryer for the site.

GDS model range

ModelHeat output, kWAir flow, m³/hHopper, m³Weight, kg
40 GDS473.3000.3250
70 GDS705.0000.53350
140 GDS1409.8000.6580
240 GDS24016.0001.0850
350 GDS35021.0001.01.140
580 GDS58132.0001.02.300
720 GDS720to suit the dryer1.02.900
1100 GDS1.100to suit the dryer1.04.400
1280 GDS1.280to suit the dryer1.05.800

For small dryers and space heating: GDP and GDM

GDP Plug and Play is a heat generator with automatic fuel feed assembled in a cabin: it arrives ready to run and is connected to the duct. Output is 75–580 kW and air flow 5,000–32,000 m³/h.

GDM units are loaded by hand with logs, pallets and briquettes and deliver 35–262 kW. Their combustion chamber and heat exchanger are also stainless steel. Both series are fitted to small dryers and used in greenhouses, on farms and in workshops.

What we need to select a unit

  • Dryer: make and model, air flow, whether it has its own fan.
  • Temperature: what you dry and at what outside temperature.
  • Fuel: chips or pellets, their moisture and size, where the fuel is stored.
  • Site: indoors, canopy or outdoors, emission requirements.

Similar machinery

Catalog
Heat generators, boilers and CHP units →
Gas and diesel generator sets
Heating, energy and biofuel

Gas and diesel generator sets

We supply gas generator sets up to 4.5 MW and diesel sets up to 21.6 MW, as well as cogeneration and trigeneration units based on them. Where more power is needed, several machines are combined into one plant. Gas…

Price on request
ICS biomass mini CHP plants
Heating, energy and biofuel · ICS

ICS biomass mini CHP plants

Mini CHP plants from the Austrian maker ICS Energietechnik generate electricity and heat at the same time from biomass — wood chips, bark, corn cobs, husk. The boiler produces steam at up to 35 bar and 500 °C, which…

Price on request
Modular biomass micro CHP plants
Heating, energy and biofuel

Modular biomass micro CHP plants

Micro CHP plants are cogeneration units with an electrical output from 35 kW to 1 MW: they produce electricity and heat at the same time. The units are modular or containerised, so capacity is added in modules of 50 or…

Price on request
Herbas heat generators for dryers: HT-90, HTG-160, HT-RD, HT-AD
Heating, energy and biofuel · Herbas

Herbas heat generators for dryers: HT-90, HTG-160, HT-RD, HT-AD

Herbas (Croatia) floor-standing heat generators heat the air for dryers. The generator usually stands in the end bay of the dryer, and its fan blows the heated air into the chamber. The same models are used to heat…

Price on request
Request

Request a price for this machine

Describe your task — we will select the machinery and calculate the price and delivery time.

+38 (066) 354-00-04 Mon–Fri 9:00–18:00

By submitting the form you agree to the privacy policy.