Herbas heat generators for dryers: HT-90, HTG-160, HT-RD, HT-AD
Herbas floor-standing heat generators for dryers and space heating: gas and liquid fuel up to 160 kW, firewood 50–150 kW, wood chips and pellets 10–150 kW.
Herbas (Croatia) floor-standing heat generators heat the air for dryers. The generator usually stands in the end bay of the dryer, and its fan blows the heated air into the chamber. The same models are used to heat greenhouses, workshops and livestock buildings.
Clean air with no combustion products
In all models the furnace is combined with a heat exchanger: flue gases give up their heat to the air through its walls and leave by the chimney, so clean hot air enters the dryer. The generator comes with an axial or radial fan, an electronic thermostat with a sensor and a control cabinet. Air flow is 14,000–30,000 m³/h.
Manufacturer’s video: floor-type container dryer with a moving floor and a turner
HT-90 and HTG-160: gas or liquid fuel
The gas and liquid-fuel versions differ only in the burner. The letter in the name shows the fuel: P for gas, U for liquid fuel.
Fuel
Model
Output
Natural gas
HT-90P
up to 90 kW
Natural gas
HTG-160P
up to 160 kW
Liquid fuel
HT-90U
up to 90 kW
Liquid fuel
HTG-160U
up to 160 kW
Natural gas: the connection has to be prepared in advance, but maintenance is simple and the fuel supply is steady.
LPG: tanks are needed, and separate regulations apply.
Liquid fuel: simpler installation and a lower initial outlay.
The burner must be connected to the tank or pipeline by a certified fitter, in line with national regulations.
HT-RD: firewood
It burns dry firewood: logs up to 1.1 m long and 20 cm in diameter, moisture up to 20%. The logs are loaded by hand into a reactor furnace where the wood is gasified, so combustion follows the pyrolysis principle. The furnace is made of boiler plate, with the zones of intense flame in refractory plate and thermal concrete. Output is 50–150 kW, and the ash is removed by hand.
HT-AD: wood chips and pellets with automatic feeding
The fuel is G20 wood chips or pellets. From a hopper of 1 m³ or more it is fed by an auger through a twin-shaft system with a rotary valve that protects against burn-back. Output is 10–150 kW. The ash is emptied by hand from the ash pan. The HT-AD is installed in a dryer bay under a canopy or inside a container.
Models compared
Parameter
HT-90 / HTG-160
HT-RD
HT-AD
Fuel
natural gas and LPG (P); liquid fuel (U)
dry firewood
G20 wood chips, pellets
Fuel feed
single-stage burner
by hand
hopper from 1 m³, auger, rotary valve
Output
up to 90 and up to 160 kW
50–150 kW
10–150 kW
Ash removal
—
by hand
by hand, from the ash pan
Space heating
For heating, a distribution duct is connected to the generator: a spiral duct with grilles or a polyethylene sleeve. This is how greenhouses, workshops and livestock buildings are heated.
ICS heat generators are hot-air generators from the Austrian maker ICS Energietechnik. They burn wood chips, bark and other biomass and deliver clean heated air to a grain dryer or another industrial dryer. Output goes…
We supply gas generator sets up to 4.5 MW and diesel sets up to 21.6 MW, as well as cogeneration and trigeneration units based on them. Where more power is needed, several machines are combined into one plant. Gas…
Mini CHP plants from the Austrian maker ICS Energietechnik generate electricity and heat at the same time from biomass — wood chips, bark, corn cobs, husk. The boiler produces steam at up to 35 bar and 500 °C, which…
Micro CHP plants are cogeneration units with an electrical output from 35 kW to 1 MW: they produce electricity and heat at the same time. The units are modular or containerised, so capacity is added in modules of 50 or…
Price on requestDetails →
Request
Request a price for this machine
Describe your task — we will select the machinery and calculate the price and delivery time.