+38 (066) 354-00-04 Mon–Fri 9:00–18:00 75 Zhylianska St, Kyiv, Ukraine

Herbas conveyors and pneumatic conveying

Herbas belt, screw, roller, vibrating and chain conveyors, pneumatic conveying, bucket elevators and diverter valves, sized for your project.

Price and configuration
Calculated for your area and conditions
Delivery
Within Ukraine and abroad, with customs clearance
Start-up and service
On-site commissioning and staff training

Description and specifications

Description

Herbas (Croatia) builds conveying equipment for its own processing lines and as stand-alone machines. Most conveyors are sized for the customer’s process, so the types, uses and parameter ranges are given below.

Types of equipment

TypeWhat it movesKey parameters
Belt conveyorsbulk and unit loadswidth 200–1,200 mm, length up to 30 m
SC screw conveyorsgrain, seeds, rose hips, herbs, powdersscrew Ø60–400 mm, length to order
Pneumatic conveying, TP-225powders, granular materials, cut plant materialparticles up to 15 mm, TP-225 route up to 40 m
Roller conveyorscompact unit loadswidth 100–1,500 mm, driven or gravity
VS vibrating conveyorspowders, granular and small lumpy materials8 sizes, incline up to 15°
HVE bucket elevatorsbulk materials, verticallydischarge height up to 10 m
Chain conveyorsboxes, pallets, drums, sacks, timberup to 1,000 kg per unit load, length up to 50 m
Diverter valvesa flow of bulk material2 or 3 outlets

Belt conveyors

They move bulk and unit loads within a line or on their own. Versions: straight, inclined, with a change of gradient, with a modular belt, and 90° curves. The belt is chosen for the product and comes with certificates, including to FDA standards.

Manufacturer’s video: belt conveyor with a 90° turn

SC screw conveyors

  • Trough: round or half-round with a small clearance for powders, fine grain and steep inclines; polygonal for fibrous materials and medicinal herbs.
  • Drive: shaft-mounted worm geared motor.
  • Cover: bolted or quick-release; dust-, water- or gas-tight versions are possible, ATEX on request.
  • Material: S235JR steel, galvanised steel or AISI 304 stainless steel.
  • Standard models: SC-9/300, SC-12/125, SC-12/380, SC-20/380, SC-20/400, SC-20/500; a 0.5 or 1 m³ hopper is offered for some models.

Y-shaped bagging augers have a fork at the outlet: while one sack is filling, the other is changed and the flow does not stop. The flap is switched by hand or by an actuator, from a level sensor or a signal from the scale. Dosing units with a large hopper and a segmented screw are built for sticky materials, and a trough with two screws for materials that tend to bridge.

Pneumatic conveying

A system consists of a dosing unit, a hopper, pipework, a cyclone separator, rotary valves and a fan. In closed systems most of the air is recirculated and the line runs under negative pressure, so dust does not escape into the building. The TP-225 model is designed for cut plant material, powders and seeds, with a route of up to 40 m.

Roller conveyors

They move unit loads on production and packing lines and on the way to the warehouse. Driven, gravity and curved versions are available; width 100–1,500 mm, length to order.

VS vibrating conveyors

They are used for dosing, spreading material evenly ahead of the next machine, emptying hoppers and fully enclosed conveying in tubes. Speed depends on the amplitude, the frequency and the angle of the suspension arms. The drive is a crankshaft, an electromagnet or vibration motors. Sticky and very wet materials are generally unsuitable for vibrating conveyors.

Standard models: VS 3/1.25, VS 6/1, VS 6/1.25, VS 6/2.5, VS 6/2.75, VS 9/2.40, VS 9/2.75, VS 12/3.25. The first number is the width in hundreds of millimetres, the second the length in metres.

HVE bucket elevators

They lift grain, oilseeds, pulses, nuts, flour and groats to a height of up to 10 m and take up little floor space. The buckets are polymer, the belt is tensioned by a screw, and at the bottom there are a clean-out drawer and inspection doors. The feed must be even. In the food-grade version the casing is AISI 304, the belt is white PVC and the buckets are made of polymers approved for food contact.

Chain conveyors

They carry boxes, pallet containers, drums, sacks, pallets and timber at 0.05–0.2 m/s. The chains slide on polymer guides. A route can include a turn through any angle and sections that rise and lower; Herbas has built systems up to 50 m long with sensors and automation.

Gravity diverter valves

Two- and three-way valves direct a flow of grain, compound feed, flour, sugar or pellets to one of the outlets and are dust-tight. They are fitted in silos, on pipework and on dosing and packing lines. The flap is driven by a pneumatic cylinder (standard) or a servomotor.

For powder coating shops Herbas also makes overhead conveyors on which parts are moved by hand.

Similar machinery

Catalog
Machinery for herbs and fibre crops →
Hemp and flax Herbas equipment for industrial hemp
Processing and lines · Herbas

Herbas equipment for industrial hemp

Herbas (Croatia) covers the whole chain of work with industrial hemp after sowing: harvesting the flowers, drying, separating the flowers from the stem and dividing the material into saleable fractions. This page…

Price on request
Hemp and flax F-2000 square baler for hemp
Harvesting

F-2000 square baler for hemp

F-2000 square baler for hemp. B2B selection of a solution for your task: configuration, logistics, commissioning and service — on request.

Price on request
Hemp and flax ZIB-2.4 flax harvester
Harvesting

ZIB-2.4 flax harvester

ZIB-2.4 flax harvester. B2B selection of a solution for your task: configuration, logistics, commissioning and service — on request.

Price on request
Hemp and flax S-1.5 mini flax harvester
Harvesting

S-1.5 mini flax harvester

S-1.5 mini flax harvester. B2B selection of a solution for your task: configuration, logistics, commissioning and service — on request.

Price on request
Request

Request a price for this machine

Describe your task — we will select the machinery and calculate the price and delivery time.

+38 (066) 354-00-04 Mon–Fri 9:00–18:00

By submitting the form you agree to the privacy policy.